[Anthill-pro] Non-Force builds...

[Eric Minick]

Thanks Daniel,

On the build request, is there a job available? Does it have a change 
log? If so, does its log indicate that it found changes?

The other place where we've seen this problem is when a workflow has the 
"Skip quiet period" option checked. The quiet period is when the change 
detection happens. So if it is skipped, Anthill will only build when forced.

Regards,

Eric

Daniel Kirsch wrote:
> Success
>
> -----Original Message-----
> From: anthill-pro-bounces at lists.urbancode.com
> [mailto:anthill-pro-bounces at lists.urbancode.com] On Behalf Of Eric
> Minick
> Sent: Monday, July 30, 2007 12:43 PM
> To: AnthillPro user and support list.
> Subject: Re: [Anthill-pro] Non-Force builds...
>
> Daniel,
>
> When you look at your build job configuration, what is the change log 
> status set to (first page).
>
> Regards,
>
> Eric
>
> Daniel Kirsch wrote:
>   
>> Jason,
>>
>> Sorry about the confusion we have submitted changlists on the
>>     
> branch(s)
>   
>> in question.  If I do not check "Force" the builds never run.
>>
>> Dan
>>  
>> -----Original Message-----
>> From: anthill-pro-bounces at lists.urbancode.com
>> [mailto:anthill-pro-bounces at lists.urbancode.com] On Behalf Of Jason
>> Schatz
>> Sent: Monday, July 30, 2007 11:54 AM
>> To: AnthillPro user and support list.
>> Subject: Re: [Anthill-pro] Non-Force builds...
>>
>> Dan,
>>
>> When we call the p4 changes command we pass it the -s submitted, which
>> means that anthill3 will only pick up changelist that have been
>> submitted to perforce.  So simply creating a changelist is not enough
>>     
> to
>   
>> trigger a build you will actually need to submit those changes to
>> perforce in order for anthill3 to register that there has been a
>>     
> change
>   
>> and kick off a build.
>>
>> Thanks,
>> Jason
>>
>> Daniel Kirsch wrote:
>>   
>>     
>>> Hello,
>>>
>>>  
>>>
>>> So we are using Perforce w/AHP and it seems that I can only do a
>>>       
> build
>   
>>> if I check the Force box on the manual builds.  If I schedule a
>>> nightly build of a Workflow it too will not do anything if Force is
>>> not selected.
>>>
>>>  
>>>
>>> What is AnthillPro evaluating to see if a build is required?  In
>>> Perforce there are new Changlists for the branch, and I had thought
>>> this was all that was needed?
>>>
>>>  
>>>
>>> Regards,
>>>
>>>  
>>>
>>> Dan
>>>
>>>  
>>>
>>>  
>>>
>>>
>>>     
>>>       
> ------------------------------------------------------------------------
>   
>>   
>>     
>>> _______________________________________________
>>> Anthill-pro mailing list
>>> Anthill-pro at lists.urbancode.com
>>> http://lists.urbancode.com/mailman/listinfo/anthill-pro
>>>   
>>>     
>>>       
>> _______________________________________________
>> Anthill-pro mailing list
>> Anthill-pro at lists.urbancode.com
>> http://lists.urbancode.com/mailman/listinfo/anthill-pro
>> _______________________________________________
>> Anthill-pro mailing list
>> Anthill-pro at lists.urbancode.com
>> http://lists.urbancode.com/mailman/listinfo/anthill-pro
>>
>>   
>>     
> _______________________________________________
> Anthill-pro mailing list
> Anthill-pro at lists.urbancode.com
> http://lists.urbancode.com/mailman/listinfo/anthill-pro
> _______________________________________________
> Anthill-pro mailing list
> Anthill-pro at lists.urbancode.com
> http://lists.urbancode.com/mailman/listinfo/anthill-pro
>
>